Published 8/13/2012

VMC, Pallet System Keep Work Flowing

A Haas VMC with a Midaco pallet changer not only freed additional capacity on the HMCs this shop uses for tight-tolerance production work, but also reduced cycle times in some cases.

Edited by: MMS Editorial Team

Dean Turek, production supervisor (left), and Scott Tibodeau, machinist, show off of K&G Manufacturing’s new Hass VMC and Midaco APC. Mr. Turek says the next time the shop purchases a VMC, it will consider incorporating a pallet changer on both sides of the machine.

K & G Mfg. uses four HMCs with a 30-pallet flexible manufacturing system (FMS) for high-volume production machining for the aerospace, computer and other industries. The new VMC-APC combo freed capacity on this system for additional tight-tolerance parts.

Tight-tolerance computer circuit board parts like this prompted the company’s search for a new VMC with a pallet changer.

Opting for a Haas VMC and Midaco automatic pallet changer (APC) rather than another HMC has paid off for K & G Manufacturing Company—literally. For less than 25 percent of the purchase price of an HMC, the system has not only freed additional capacity on the HMCs traditionally used for high-tolerance production work, but also reduced cycle time in some cases.

Harry Kane and Sid Gerbig founded K & G in 1937 as an automotive parts distributor serving dealerships and service centers. They added a machine shop to the business at the beginning of World War II to produce parts for the war effort. By the mid ‘50s, the company had switched to manufacturing tools, dies, jigs, fixtures and special machinery. A decade later, it expanded into full production-machining services. Today, its 60-plus employees work to produce parts for the aerospace, defense, marine, computer and medical industries.

The company’s 41,000-square-foot, climate-controlled facility is home to four HMCs serviced by a 30-pallet, flexible manufacturing system (FMS); three standalone HMCs; three standalone VMCs; seven lathes; and one twin-turret, twin-spindle lathe. It also houses a tool crib where all loading is preset, a quality department with two CMMs, a deburring department, a pressure-testing department and an assembly department.

The problem that led the company to purchase the new VMC and APC involved the four-HMC FMS. “The four machines were all booked, some running computer circuit board parts, and we needed to offload some of this work to make room for additional tight-tolerance parts,” says Dean Turek, K & G production supervisor. “Even though we run a lot of aerospace parts, we figured we did not need to run all those parts on the horizontals to get the tolerances we needed.”

Seeking a less-expensive VMC, the company decided on a package consisting of a VF3SSYT VMC from Haas Automation (Oxnard, California) and a A4025SD APC with cast-aluminum pallets from Midaco (Elk Grove Village, Illinois). Since installation, the system has been used to run both low- and tight-tolerance work as well as both aerospace and non-aerospace parts—in some cases even faster than the HMCs, Mr. Turek says. As an example, he cites a three-minute cycle time improvement on the aforementioned circuit board components. As for the lower cost of this system versus another HMC, “That type of savings is huge in helping us stay competitive,” he adds.

For further time savings, the company purchased four additional pallets and set up a pallet storage area with a transfer cart for moving them between the storage area and the machine. This setup enables staging jobs offline and transferring the pallets to the machine when ready. The fact that the pallets provide repeatability accuracy within ±0.0001 inch makes this strategy especially useful for significantly limiting downtime between jobs, Mr. Turek says. Operators can typically swap out both pallets on the Midaco shuttle within 5 to 10 minutes.

The next time the company installs a VMC, it will explore the idea of putting a pallet changer on both sides of the machine instead of just one side, Mr. Turek says. Having a shuttle on both sides would make four pallets available for immediate use, thereby enabling the machine to run longer without operator attention. Considering plans are in the works to replace some aging VMCs on the shop floor, this is likely to happen, Mr. Turek says. “We wouldn’t just buy another vertical machine alone. It will be purchased with a Midaco. That’s not even a question.”

Related Content

Automation 20 May 2024

Using Automation to Reduce COGS and Stay Globally Competitive

Decade-long, multiphase automation investments lower operating costs and maintain technology lead in an increasingly competitive global market.

Tooling 10 Jan 2024

Shop Reclaims 10,000 Square Feet with Inventory Management System

Intech Athens’ inventory management system, which includes vertical lift modules from Kardex Remstar and tool management software from ZOLLER, has saved the company time, space and money.

Medical 12 Jun 2024

Orthopedic Event Discusses Manufacturing Strategies

At the seminar, representatives from multiple companies discussed strategies for making orthopedic devices accurately and efficiently.

Tooling 10 May 2024

Eight Articles to Understand Live Tooling

A roundup of the most read articles about live tooling on 91��.

Cutting Tools

A New Frontier in Surface Finish Control

What if your machine tool could measure surface roughness as it cuts? This article explores how in-process metrology is advancing from concept to reality, enabling real-time feedback, immediate detection of anomalies and new levels of control over surface quality. Discover the technologies making this possible.

Workforce Development

How I Made It: Dennis Rymanowski

Dennis Rymanowski has worked at NSH USA for 60 years, with his passion for manufacturing living alongside his passion for his family’s polka band.

VMC, Pallet System Keep Work Flowing